JUNIPER SSG5 CONFIGURATION GUIDE PDF

JUNIPER SSG5 CONFIGURATION GUIDE PDF

CRITICAL NOTE: We have found that IPv6 pings sent to the Juniper SSG5 will cause the device to REBOOT. Turning off From here, select the default of “Use the Initial Configuration Wizard instead.” Download Business Routers Guide. Secure Services Gateway 5 users manual details for FCC ID OXVSSG5 made by Juniper Networks Inc.. Document Includes User Manual Every effort has been made to ensure that the information in this manual is Juniper Networks, NetScreen, and ScreenOS are registered trademarks of Juniper.

Author: Digar Dougis
Country: Switzerland
Language: English (Spanish)
Genre: Career
Published (Last): 2 July 2010
Pages: 440
PDF File Size: 16.57 Mb
ePub File Size: 17.93 Mb
ISBN: 528-6-38668-698-9
Downloads: 46536
Price: Free* [*Free Regsitration Required]
Uploader: Tojadal

Notify me of follow-up comments by email. The switch ports which are configured with this IPv4 address vary! If you have forgot your password I’m not aware of any other method other than to reset the device and reconfigure it. The same concept applies to the other models ss5g support NSRP; the difference being the interface notation or dedicated HA port. The console will confirm the config erase sequence is complete and the firewall device will begin a full ocnfiguration. Here are some hidden commands that help while troubleshooting the ALGs:.

Connect to the Juniper SSG firewall console port with a console cable so you can see the output as you reset the device.

Yes – Enter the command: Only one digital certificate is required for an NSRP cluster. To display the most detailed information about active flowsfor example to see which policies trigger or which routing table lookups are used, etc. You need to use a paperclip or similar.

  M7208 MANUAL PDF

How to configure Juniper SSG

This process is quite simple once you get the timing guie. What are the minimum NSRP commands required? And to do a manual failover. The traffic log shows already finished sessions of course only if they were logged:.

Blog Webernetz.net

These instructions were performed on a SSG Repeat steps 2 – 6 for Firewall-B. To define a single name for all cluster members, type the junuper CLI command: Then continue to Step 7. I had some trouble with the application layer gateway functionality on the ScreenOS devices.

Then proceed to the next step when ready to configure NSRP. Whilst the information configufation is correct to the best of my knowledge, I am not reponsible for any issues that may arise using this information, and you do so at your own risk.

Firewall’s with identical ScreenOS versions and license keys Firewall’s with identical hardware At least one interface on each firewall to be configured in the HA zone, which will be used for carrying control channel information For more information on the software and hardware requirements for NSRP, refer to KB Defining a single name for all cluster members allows SNMP communication and digital certificates use to be continued without interruption guidf failover.

This command must be used on the current master! Perform basic configuration on Firewall-A. Your email address cofiguration not be published. The default login is netscreen: Thanks and continue the good job.

Designed and Hosted by Andy Barnes. Bind the interfaces to the zones desired, and configure an IP address on the interfaces.

Each NSRP cluster member can have different host names. This website uses cookies to improve your experience. When it arrived the config had not been erased as stated, but I’ve done this before on a Netscreen and the process is exactly the same for both Juniper Netscreen and SSG firewalls.

  ELECTRO HARMONIX 300B PDF

Once the cluster id is set to a value, all the security interfaces will become part of the VSD-group 0, by default.

Knowledge Search

The basic configuration steps for the following topology are documented in this solution. Notify me of new posts by email.

Configure NTP command, if applicable. Both ways are explained here. To do a factory reset you can either use the reset pinhole on the device or login to the serial console with the serial number as username and password.

Juniper Networks – [ScreenOS] Basic configuration steps of Active/Passive High Availability (NSRP)

Leave this field empty. Configure the NSRP cluster id: You do not need to do this but without seeing the reset confirmation prompts, it might take you many failed attempts in the dark! Other NSRP firewall pairs on the same segment must have a different set of cluster ids. For more information on assigning the HA ports, refer to KB As always before performing anything; check, double check, test and always ensure you have a backup. For assistance with configuring a pair of firewalls for NSRP, follow the steps below.

Now the device has erased the configuration and rebooted, a login prompt will be displayed.