TS2, TS2L. Software Versions: Automation Controller – build or later. ELAN SC1 – ELAN TS2 – or newer g!Tools The SC1 allows the g! Series controllers to communicate with the ELAN SA and TS2 and TS2L. It may provide interface to additional ELAN ViaNet legacy. The TS2/TSL2 is built around ELAN’s category defining, award winning OLED Touchpads. It features a ” OLED display. With Elan’s g! interface the TS2/TSL2 .
|Published (Last):||20 April 2010|
|PDF File Size:||3.19 Mb|
|ePub File Size:||18.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
Purpose of this Manual This manual provides step-by-step installation instructions and connection examples, along with basic user information for installation and ongoing use of the TS2. This manual is written for the installer of this equipment.
Organization The following information is contained in this manual. The interface provides meta data feedback no cover art at this time for supported two way devices or customizable single or multi-page interfaces for one way device control. ELAN recommends test fitting a unit prior to installation.
Run Cat-5 wire from the central equipment location head-end to the location where each Touchpad will be installed. TS2 Touchpads for outdoor use.
Mounting Height The TS2 has no viewing angle limitations, elaj mounting height should be determined by the average height of the user. Typical mounting height is inches from the floor to the bottom of the electrical box. This will provide optimum viewing for the largest number of people. Close the touch rlan. Replace the two film screws.
Replace the wall plate. All applications will use the RJ connector, while certain situations will require the use of the Interface Port.
Multifunction home automation system touch screen / wall-mounted – TS2 – ELAN HOME SYSTEMS
IR receiver in the TS2. Pressing a button on the TS2 will not issue IR commands from these outputs. NET port on the System Controller. NET port on the SC1. NET and TS2 configuration information. See the TS2 Integration Note for more information. Using the address noted in step 3 identify each touchpad on the Configuration Software Interface Tab and configure the desired zones, partitions, control, and backlight behavior.
The Service Menu continued Speaker The TS2 features a small speaker that allows audible feedback signals to be heard as a result of button pushes. The speaker can be enabled or disabled in the Service Menu.
The IR sensor can be enabled or disabled in the Service Menu. The light sensor can be enabled or disabled in the Tss2 Menu. The light sensor should be calibrated with the room lighting at its brightest setting. EDIT again if you wish to make additional changes.
The home interface displays time and basic weather information. Pressing the Media icon will change the display to the Source select page.
The currently selected source in the zone will be highlighted. Media Select Buttons When the source is selected the TS2 will display the main control page for the selected source. Tw2 Source Internal Player Figure Theater Keypad Figure You may cancel the command as well.
Elan g! TSL2 LCD In-Wall Colour Touchscreen | The Listening Post Christchurch and Wellington |
Security Page Keypad The TS2 display will change back to the main security screen and the new alarm status will be displayed and highlighted. Check for ambient light shining on the IR receiver. Check for flooding from plasma or LCD monitors.
See pages 16 and 25 for more information. Pressing sub- Sub-system i. Also See for TS2 User manual – 4 pages. Page of 49 Go. System Design and Installatio Table of Contents Add to my manuals Add. Preface Purpose of this Manual This manual provides step-by-step installation instructions and connection examples, along with basic user information for installation and ongoing use of the TS2.
Table Of Contents Chapter 3: Page 4 Media Page Ts2 Features The interface provides meta data feedback no cover art at this time for supported two way devices or customizable single or multi-page interfaces for one way device control. Rough-in TS2 Touchpads for outdoor use. Initial Ts2 Integration 1.
This website appears to be a copy of the original and may not be safe to view.
Speaker The Service Menu continued Speaker The TS2 features a small speaker that allows audible feedback signals to be heard as a result of button pushes. Page 32 EDIT again if you wish to make additional changes. Page 37 Figure Source Page Samples Note: Page 43 You may cancel the command as well.
Page 45 Figure Troubleshooting Check for ambient light shining on the IR receiver. Comments to this Manuals Your Name.
Elan ts2 installation manual
Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print.
Don’t have an account?