BCC datasheet, BCC pdf, BCC data sheet, datasheet, data sheet, pdf, Boca Semiconductor Corporation, 30 V, PNP silicon planar epitaxial transistor. BCC Transistor Datasheet pdf, BCC Equivalent. Parameters and Characteristics. BC Silicon PNP Transistor. Audio Amplifier, Switch. Features: D Suitable for AF-Driver Stages and Low Power Output Stages. Absolute Maximum Ratings.

Author: Daill Tatilar
Country: Laos
Language: English (Spanish)
Genre: Art
Published (Last): 1 January 2010
Pages: 89
PDF File Size: 1.23 Mb
ePub File Size: 4.13 Mb
ISBN: 417-5-71407-727-8
Downloads: 94288
Price: Free* [*Free Regsitration Required]
Uploader: Nikokazahn

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. The BC because of this large gain value is normally used to as a audio amplifier.

Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. This is known as the biasing. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

Xatasheet based GPS receiver.

BC is a general purpose PNP transistor. Skip to main content.

Choosing Battery for Robots. The voltage divider is the commonly used biasing mode. BC is a PNP transistor hence the dattasheet and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.


The value of this resistor RB can be calculated using below formulae. Submitted by admin on 26 March Complete Technical Details can be found in the BC datasheet given at the end of this page. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. The DC current gain varies in range to It is also used as a complement for transistors BC to BC Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers.

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. BC is used in common emitter configuration for amplifiers. It can amplify power, voltage and current at datasheft configurations. This high-density System-in-Package SiP integrates controller, power switches, and support components.

Interface GPS with Arduino. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be datasueet by supplying the required amount of current to the base pin.

Transistor BC558

Virgin Galactic — Commercial Space Flight. It is used in switching and amplifier applications. The input signal at base is amplified and taken at the emitter. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as datasgeet above. The transistor terminals require a fixed DC voltage to operate in the desired region of its bc558cc curves.


For amplification applications, the transistor is biased such that it is partly on for all input conditions.

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. BC has a gain value of to ; this value determines the amplification capacity of the transistor.

BCC Datasheet(PDF) – Weitron Technology

TL — Programmable Reference Voltage. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Amplifier modules like Audio amplifiers, signal Amplifier etc. In the absence of base signal, it gets completely off.

A resistor is always added in series with base pin to limit the base current. A Transistors acts as an Amplifier when operating in Active Region.

BC558 Datasheet, Equivalent, Cross Reference Search

What is Web Browser. SPI Module of Arduino. Interface SD Card with Arduino. Choosing Motor For Robots.